DIY Cattle Panel Trellis - Countryside (2024)

Reading Time: 5 minutes

By Romie Holl – As I get older, the desire to get on my knees to work in the garden becomes less, so I needed to figure out an inexpensive way to avoid all of the bending and crawling on the ground. A cattle panel trellis is just what I was thinking. All of my grape vines were within three and a half feet from the ground, so picking the grapes and trimming the vines took a long time, not to mention my back and knees were talking to me when finished.

Grapes need a heavy, strong trellis, so I decided I would use cattle panels and build my own cattle panel trellis. If you don’t know what cattle panels are, they are made from very heavy-gauge wire (roughly 1/8- inch in diameter), and are 16 feet long. The cattle panels are 50 inches tall and have roughly eight- inch squares between rows and columns. (There are other panels to choose from: for example, hog panels are 36 inches tall and have smaller holes.)

I like the cattle panels for three reasons:

• The extra height means I need to buy fewer of them (they are roughly $25-$27 where I live).

• They are plenty strong to hold the grapes.

• They are galvanized and will outlast my lifetime.

[optin-monster-shortcode id=”k7fvz8wek0u9ohtoglrz”]

By placing one panel vertically, that gave me three to four feet before the start of the arch on the trellis, depending on how much overlap was used. This much vertical structure will allow me to walk under the grapes, pick the fruit, or trim the vines. And if the panels are overlapped by two inches (giving 48 inches), four panels will be needed for the arch. So, for a 16-foot trellis, I will need six panels ($120 worth).

Now, how wide can I make it? For the arch, I wanted at least a one-foot overlap to provide strength. After laying it out, the trellis could be 12 feet wide without cutting any of the panels.

After measuring the existing grape vines, I calculated that the new trellis will need to be 32 feet long, and I will need two of them. This means 24 panels total. I bought 28 panels as I would rather have too many than not enough.

I built the cattle panel trellis in early spring before the grapes started to grow. I removed the vines from the old trellis with care and I gently laid them on the ground. I drove pipes into the ground every four to five feet to support the vertical panels.

DIY Cattle Panel Trellis - Countryside (1)

When I placed the vertical panels, I made sure to put them on the inside and the pipes on the outside. This will give the most strength to the trellis. I used plastic zip ties to hold the vertical panels in place, and after all the vertical panels were done, I went back through and used heavy 12-gauge wire to tie them permanently in place.

Removing the old trellis, pounding the new poles in the ground, and installing the vertical panels took three hours. I was done for the day and the animals were ready to be fed.

The next day, it was time to start the arch section of the panels. I carried a panel to the far end and put a corner on the ground against the vertical panel to hold it in place. I then went to the other end and it made an arch with very little effort. Once both end pieces of the panels were on the ground, they were placed at the end of the vertical panels. This was done six more times for a total of seven per row. I purposely left one panel out of each row at this time.DIY Cattle Panel Trellis - Countryside (2)

The next steps can be done by yourself but having a partner will help. Starting on one end, I lifted a panel and used plastic zip ties to hold it in place. Then on the same panel, I went to the other side, lifted it, and wired it in place. Going on to the next panel, I overlapped it to the first panel as I lifted the first side (trying to keep a two- inch overlap). I did this two more times on that end of the row. Then I walked down to the other end of the row and started on that side. Once all arches were done that were placed in the row, there was a big gap. Both ends of the arches matched perfectly with the ends of the vertical supports. The final arch bridged the gap left behind. My rows were nowhere near perfect, so there was more of an overlap than the two inches. But once the grapes start growing, I won’t see it.

To permanently tie the arches to each other as well as the vertical panels, hog clips and pliers were used. These are heavy- duty C-shaped clips. The pliers have a groove in them to hold the clips until they are squeezed into place. The hog clips were installed roughly 18 inches apart.

Today’s project work was done and the animals wanted to get fed again.
The next step is to take scissors and cut off all of the plastic zip ties. I ended up with a grocery bag full.

Since the cattle panel trellis was built before the grape vines were growing and were still stiff, the project was done for now.

A month later, the grape vines were leafing out and the vines were flexible again. It was now time to finish this project. Being careful to not break off the brittle young shoots, I tied them to the trellis. I used baling twine for this. Not only is it cheap and strong, it also biodegrades in time. When
tying the vines, I left plenty of room for future growth. I left about an inch bigger than the vine.

In the summer, it’s nice seeing all of the grapes growing and noticing how easy they’ll be to pick when they’re ripe. With this arch trellis, it is much easier to trim the vines as needed. The trellis lifts the vines away from the ground, making it easier to weed-wack the grass away.

DIY Cattle Panel Trellis - Countryside (3)

The extra panels that I bought were not needed for the grapes, but will be used for growing peas, beans, cucumbers, etc. in the garden.

Will you be building a cattle panel trellis of your own? Please share your experience in the comments below. We would love to hear from you!

Originally published in Countryside and Small Stock Journal November/December 2020, and regularly vetted for accuracy.

Insights, advice, suggestions, feedback and comments from experts

About Me

I am an expert enthusiast with a deep understanding of a wide range of topics. My expertise is demonstrated through a comprehensive understanding of the subject matter, as well as the ability to provide detailed and insightful information. I have a wealth of knowledge and experience in various fields, allowing me to offer valuable insights and assistance to users seeking information and guidance.

Cattle Panel Trellis

This article discusses the construction of a cattle panel trellis for grape vines. This type of trellis is made using heavy-gauge wire panels, typically 16 feet long and 50 inches tall, with roughly eight-inch squares between rows and columns. The trellis is designed to provide support for grape vines, allowing for easier maintenance and harvesting. The author highlights the benefits of using cattle panels, such as their strength, durability, and cost-effectiveness.

The construction process involves setting up the vertical panels, creating arches, and securing the structure in place. The author also emphasizes the importance of proper installation techniques, such as using plastic zip ties and heavy-gauge wire to ensure stability. Additionally, the article discusses the practicality of the trellis, including its ability to facilitate vine maintenance and harvesting, as well as its potential for use in growing other crops like peas, beans, and cucumbers.

The detailed instructions and personal experience shared in the article provide valuable insights for individuals interested in constructing their own cattle panel trellis for grape vines or other crops. The practical tips and considerations outlined in the article can serve as a helpful guide for anyone looking to embark on a similar project.

If you have any specific questions or need further details about the construction or maintenance of a cattle panel trellis, feel free to ask!

DIY Cattle Panel Trellis - Countryside (2024)
Top Articles
Latest Posts
Article information

Author: Kelle Weber

Last Updated:

Views: 6048

Rating: 4.2 / 5 (73 voted)

Reviews: 80% of readers found this page helpful

Author information

Name: Kelle Weber

Birthday: 2000-08-05

Address: 6796 Juan Square, Markfort, MN 58988

Phone: +8215934114615

Job: Hospitality Director

Hobby: tabletop games, Foreign language learning, Leather crafting, Horseback riding, Swimming, Knapping, Handball

Introduction: My name is Kelle Weber, I am a magnificent, enchanting, fair, joyous, light, determined, joyous person who loves writing and wants to share my knowledge and understanding with you.